0
Do you offer screws other than those that appear in your catalogue?
Yes, on demand. We offer a wide range of screws for soffits, siding, fiber cement panels, etc. Contact us for more info.
Which bit do you recommend for the Phillips cross head screw?
We recommend the Phillips #2 bit.
Do we have to pre-drill the fiber cement panels before screwing on a wooden structure?
No, pre-drilling is not necessary.
What is the advantage of using a grade 8 screw?
Using a grade 8 screw creates less pressure on the fiber cement panel. Therefore, reducing the risk of breakage. Since it is also smaller, for example than a grade 10 screw, it creates less fiber cement residue on your siding.
Why do you sell #8 grade screws?
This is the grade recommended in James Hardie’s January 2020 best practices guide.
How long does it take to fill an order for screws in JH Statement colours?
24 hours (they are always in stock).
Can I screw in the panel at the same time as the trim?
Yes. However, it is important to pre-drill the panel and trim to prevent the panel from lifting up along the screw and breaking.
Can an improper installation invalidate the warranty for trims?
No. Regardless of how the installation is done, Light Trim trims remain covered by the warranty. Nevertheless, we urge you to carefully follow the manufacturer’s recommendations for the installation of your fibre cement.
Do trims replace sealant joints?
Yes, you avoid the need to use sealant when using Light Trim trims.
Do the trims make siding waterproof?
No. Trims make it easier for the water to run off the siding. Watertightness must be ensured before installing the siding.
Do I need to protect the trim edges once they have been cut?
No. For a more esthetic finish, you can order a container of touch-up paint.
How should I cut the trims?
A light metal blade remains the best option. Otherwise, grinders are also suitable.
Why don’t you have a primed finish?
Primers have a waiting period before repainting. Paint provides more flexibility and a similar adhesion to primer.
Can I repaint the trims?
Yes, our trims are very easy to repaint. They do not require any chemical treatments, such as anodizing.
Is the male section of trim J002 painted?
Yes, the male section is the same colour as the female section.
How do I attach outside corners C224 and C994?
See links : C224 et C994.
Can trims C224 and C994 slide?
No They are designed to be attached without sliding
Can trims V099, V920, V220, and J002 slide once they have been installed?
Yes. You have three options: 1. Press in the trim along the horizontal lines.ng des lignes horizontales. 2. Put a little construction glue in the indentation of the female section. 3. Use a small self-drilling soffit screw to join the two sections.
I am having trouble with trims V099, V920, V220, and J002. What should I do?
Make sure that the back section is firmly pressed in along the sides.
Where should I attach the fasteners on trims?
Each trim has a slight indentation for easy fastening.ée d’une légère indentation pour faciliter la fixation.
How many nails or screws should I use to attach the trims?
A fastener every 16 inches is sufficient.
How should I attach the trim on steel laths?
By using an ET&F 510 nailer or modified truss head self-drilling screws.
How should I attach the trim on wooden laths?
By using a siding nailer and nails that are one inch long or longer.
How many screws should I use for each fibre cement panel?
Each fibre cement manufacturer sets its own standard for the number of screws required. Refer to your siding manufacturer.
What type of paint do you use for your screws?
All screws are hand painted and then put into a 375-degree oven to provide maximum paint hardness. Our paint is compliant with AAMA 2604, as are our trims.
Should I use nickel or stainless steel screws for fibre cement panels?
Refer to the siding manufacturer’s recommendations.
Should I leave a 1/8-inch gap at the bottom of the trims?
No It is not necessary. Since fibre cement is very stable, you can press the fibre cement siding into the bottom of the trims.
Is your trim format suitable for fibre cement?
We fully comply with the strict installation criteria set by fibre cement manufacturers.
How is the paint quality?
Our trims are painted in compliance with the highest standards and PPG. In accordance with AAMA 2604.
Should I use nickel or stainless steel screws for fibre cement panels?
Refer to the siding manufacturer’s recommendations.
Where are the trims manufactured?
The trims are made of extruded aluminum and are 100% Canadian-made.